Saturday 17 November 2012

POST 42 - NOVEMBER 2012 - ELECTRIC WATER PUMP

I know I've mentioned this a few times in the past but just to re-cap:
A few years back, my 140 suffered from overheating on hot days and nasty heat soak issues. I more or less sorted this with an aluminium radiator, larger fan and additional electric fan, but also looked around for some alternative solutions.
An email conversation with an Australian enthusiast revealed that a common solution in the very hottest parts of that continent is to fit an electric water pump and to this end a company called Davies Craig manufacture just such a range of devices.

Davies Craig EWP115 Water Pump from Australia

A little research highlights a few other benefits:
A conventional pump is most of the time creating much more flow than needed but more importantly, sometimes not enough. With proper control, an electric pump's speed / rate of flow is determined entirely by engine temperature with the flow continually adjusted to maintain a 'set temperature point' regardless of external temperature and load.  This also negates the requirement for a thermostat and by-pass hose, thereby simplifying the cooling system.  The Davies Craig control system actually goes a little further. 
Temperature sensor will live where the Otter switch once resided.
A manual choke switch will take over from the hit and miss Otter.
On start up, to minimise engine warm up time, the pump just pulses, to avoid hot spots forming around the cylinder areas, then gradually ramps up to normal operation and maintains the 'set point'.  This can be programmed in anywhere from 75 to 95 degrees for either max performance or max economy.
Switch off and the pump will continue running just long enough to resolve the XK engine's heat soak issues.  The Control unit also operates an electric fan to work in conjunction with the pump.
Given that the Alternator is mostly generating unused power, and some of this is now running the pump, its a bit of a free ride, and with no belt driven mechanical pump, will give a small but real increase in engine power. 

Apparantly, the normal approach to installation is to simply remove the impeller or vanes from the existing water pump.  This means there are no belt or pulley issues to worry about, but the angle of the water inlet, at least on my car, pointing downwards makes the pump and pipe arrangement very awkward.  Additionally, it would be good to create some space behind the radiator to accommodate an electric fan.  I am also not happy about wrecking my original pump if the whole scheme ends in tears, which is entirely possible.  It shouldn't be too hard to make up a blanking plate with a water inlet pointing the right way so this is my starting point.

First try.  Shame it's destined for the scrap bin.
The inlet comes from the old radiator top hose fitting, cut down and welded to an 8mm alluminium plate, cut and filed to shape.  The plan is to simply drive the dynamo (now an alternator) directly from the crank (bottom) pulley.  Only when I try to establish the new V Belt size does it dawn on me that the dynamo adjustment now forms a perfect arc around the bottom pulley, so without the water pump pulley, the V belt cannot be tensioned.  Clearly whats required is a blanking plate which can incorporate an 'idler' pulley in place of the water pump pulley.  I roughly draw up what I think is required and contact proper engineer friend Christian for advice.

Now with added idler pulley - My drawing as a starting point
CAD / CNC drawings and machining.

In spite of his occupational workload, young family and ongoing E-Type restoration, Christian still finds time to convert my drawing into a CAD format and arranges to have the parts produced  using CNC water jet cutting and milling.

Converted into a proper CAD drawing

And then into actual parts - Everyday stuff for these guys but still
amazing to me.
Christian very wisely gives me the component pieces to play with before they are all welded together and it soon becomes obvious that the idler pulley idea is a complication we could do without.  Also the different water pumps and pulleys used throughout the XK engines life would mean that this aspect of the design would need customising for each iteration.  Another friend, Neil suggests using a pulley on the back of the belt (Cam belt style) as an alternative and the following day drops by with his collection of used cam belt tensioners (What else do you collect Neil?)


Cam belt tensioners - Good idea Neil, and nicely followed
through with a selection to choose from.

The simplest from the selection turns out to be a perfect solution.  Amazingly it fits exactly onto the block which was originally intended to hold the idler pulley bearing housing and I just need to have a special stepped bolt made to accommodate it.  I do have one small problem, I have no idea which modern car it is used on so if you recognise it please let me know. 

This is just so simple it's almost elegant - and it works a treat.
Much easier than adjusting the dynamo.

Just needs plumbing in.

The rest of the job is basic plumbing but needs to look good.  I think the pump will be located  just behind the RH front engine mount where most conveniently the block has a couple of bolts attached which appear to serve no purpose.  I can attach to these, some form of 'tray' with rubber base which the pump will simply sit on.  The inlet pipe to the blanking plate needs a heater inlet fabricating onto it and I am now wondering if  a booster pump should also be used to ensure the heater matrix is provided with a plentiful supply of hot water.  Anyway, that can all be sorted out in due course and I really need the engine back in before I start to seriously look at the plumbing part of the project.  I would expect that to happen around next spring.

Miscellany
Classic Car show at the NEC tomorrow - (Sunday 18th Nov)  Travelling down by bus, arranged by TYMC (local car club) Round trip of 360 miles - cost £18.00 !!!  Delivered to the NEC front door, no parking hassles or charges and I can read, talk or sleep all the way there and back.

Next Post beginning of December.

Sunday 4 November 2012

POST 41 - NOVEMBER 2012 - BUMPER CHALLENGE

With the body correctly fitted to the chassis and an initial measurement of the door gaps also looking good, confidence is high.  Contemplating what to do next, I start thinking about the complexity of the front bumper mountings.  I have a vague recollection of the assembly being made up of quite a number of parts and have a dig around until I discover the the box of relevant bits and a few notes I'd made when dismantling.  The front bumpers are fastened through the body with extended screws to a heavy steel bar running inside the full width of the body and in front of the chassis.  I've had this bar powder coated satin black and decide to temporarily pop it into place to get a better idea of what's involved.  I was always pretty good at Chinese Puzzles, but there is no way that I can wheedle the damned thing into place.  Before giving up I post a question on Jag Lovers Forum asking if anyone can help.  Back comes the answer - yes its extremely difficult but possible. Only problem is, no one can remember how they did it.

Bumper support bar, henceforth known as 'That Bastard Bar'
Over the next few days, this develops into a 'Visitors Challenge' and many happy hours are spent with various restoration aficionados spending hours prostrate, skinning knuckles and cussing.  In the meantime I busy myself sorting out the various other bits and pieces for both front and back bumper installation.

Over 30 parts per side.  Body sits between rubber washers.
Note - Bumper Iron is body colour and support bars behind are black.
By the Weekend I've concluded that the only way to resolve this is to lift the body back off, which looks like a depressingly large amount of work.  In common with most restorers I absolutely detest retrograde steps, so clearly the best approach is a couple of days R&R in preparation for the task.

Months ago I committed to write a review of Bernard Viart's new XK120 Explored book for JDC Magazine, as soon as it became available.  I received an advanced copy on the 25th October so this undertaking served as a welcome distraction. By Sunday afternoon I'm thoroughly bored with my computer screen and ready for some retrograde action.  Including rigging up a couple of hoists, the entire operation took just two and a half hours and by 4.00pm I have the body suspended 18 inches above the chassis and the bar loosely fitted in place.

Body now swathed in protective flannelet and suspended on two hoists

'That Bastard Bar' finally in position
The only items I'm not entirely happy with are the four screwed extensions which hold the bumper brackets to the support bar.  Although only the hex-nut part is seen they do look a bit rough.  Rob at Romax Powder Coaters takes them in to see what he can do, and a couple of days later produces a brand new stainless set, knocked out on his lathe at home - amazing!

Thanks Rob at Romax Powder Coaters - Lovely surprise.
Fitting up the extension screws with the various spacers and sandwiching the body between the rubber washers whilst ensuring that all the angled bits are correctly orientated is fiddly and takes a bit of practice, but by the time I'd done the fourth one I had the job down to a few minutes.  I'll leave the bumper Irons in place to hopefully afford some protection to the body during the fit up.

Hard to believe that this


became this.


and then this

Water Pump Conversion
Still not got my bits back from the machine shop, but am advised that the new housing / inlet is being made up in stainless rather than aluminium.


 
Miscellany

MXK 120 - Another 120 OTS
Jill Thompson bought her 120 OTS project a few years back for her handy man Andy to restore, but it was delayed because a house restoration took precedence.  With both house and garage now completed, the time had come to awake the car from it's slumbers in a local farm shed and introduce it to its new home just a few miles from mine.  And so it was that last Sunday morning I gave Andy a hand to move it.  Fortunately for Jill, Andy's quite an conscientious sort of lad with a good work rate, so as long as he's kept focused and not distracted with his wood chopping and burning obsession, it shouldn't take him too long.

Deja Vu   Reg MXK120   XK120 OTS    660386
Photo - October 2012
My car Reg KRU600   XK120 OTS    660295
Photo - December 2010
 
Chassis Number 660386 was registered in December 1950, the same month as my car (660295).  It's remarkable that it lived the dormant part of its life in Teesside.  I actually saw this car as a stalled restoration at a local paint shop back in 1976 and often wondered what became of it.  As a project, it's fairly similar to my car but is complete with bonnet, boot lid and windscreen.  It has a light coating of surface rust but is generally quite solid.  It will probably need the same bits replacing, sills, B posts etc. but needs a bit more work around the headlamp pods.  Engine and gearbox are removed but came with the car.  Andy still has a few more jobs on his 'to do' list and tells me that consequently the most likely start date proper will be June 16th  next year.  Something familiar about that date.


Jill says it all looks pretty straight forward and Andy can crack
on just as soon as he's got rid of the rabbits and put the clock right.
    Note Registration Number.
This brings the total of XK120's that I know of, within say a 20 mile radius to seven, five of which are Roadsters (OTS), one Fixed Head and one OTS Replica but with mostly XK running gear and trim, also a C Type rep with a LHD 120 OTS Chassis plate. 


Next Post Mid November